Nano V6 SIM wired-mic kit instructions

Nano V6 uses its own Nano SIM for telephone calls. It is not a Bluetooth audio kit or a microSD player. The magnetic Nano earpieces do not charge; the induction unit has the rechargeable battery.

• Two passive magnetic Nano earpieces.
• Extraction magnet and extraction rod.
• Nano V6 induction unit with wired microphone.
• USB charging cable.
• If your selected order includes a Vip Pro receiver: that receiver and two listed 337/SR416SW cells. These items are conditional, not part of every Nano-only selection.

Check your selected receiver option and contents against your order before fitting any optional receiver cell.

1. Switch the unit off

   Keep the unit off while charging and when it is not in use. Use its USB charging cable with a charger rated no higher than 5V, 1A.

2. Read the charge indicator

   Flashing red means charging. Steady red means the charge is complete. The stated charging time is approximately 1–1.5 hours; use the indicator to check completion. The listed operating time is approximately 3 hours, and varies with use.

1. Test the SIM in a phone

   Confirm that it can make and receive calls and has coverage at your intended location. The kit requires the SIM PIN to be disabled before use; follow your phone’s SIM security settings and your network’s guidance. This is a SIM setting, not the phone’s screen-lock code.

2. Check the network before use

   The listed radio bands are GSM 900/1800 and LTE B1/B3/B5/B7/B8/B20 (2100/1800/850/2600/900/800 MHz). Ask your network whether it supports the device and telephone calls on those bands at your location. A matching band alone does not establish operator compatibility in the UK, USA or elsewhere.

3. Fit the Nano SIM while off

   Use the slot on the side of the unit. Follow the slot’s physical orientation; do not force the card. Seat it until its retaining mechanism clicks.

Press SOS briefly once to switch on. A blue light appears briefly and then goes out. A table audio test should produce the spoken start-up prompt “System ON”. The wired microphone must remain uncovered.

Moving the induction unit nearer or farther from the receiver changes the audio level. Keep the unit in its intended neck/chest position.

The SOS label is a device function, not an emergency-service or safety guarantee. Automatic answering and the configured outgoing SOS call require a contact to be set first.

1. Add your chosen contact

   Send an SMS to the number of the SIM fitted in the kit using add#NUMBER#. Replace NUMBER with the contact’s telephone number. The stated initial format omits the country code; if automatic answering does not work, the instructions say a numeric country prefix may be needed. Use the correct format for your country and verify the result with that contact.

2. Check the response and behaviour

   The documented confirmation text is add sos succesess. A call from the configured contact is answered automatically after approximately 3–5 seconds. With the unit already on, one brief SOS press calls that configured contact after approximately 3 seconds.

3. Remove the contact when required

   Send del#NUMBER# to the kit’s SIM number, using the contact number being removed. The documented confirmation is delete sos succesess.

Nano magnetic receiver

Nano earpieces have no receiver cell to fit or charge. Identify both small earpieces, the separate extraction magnet and the rod before the table test.

Optional Vip Pro receiver

Follow this section only if your selected kit includes a current Vip Pro SuperMini or UltraMini receiver.

1. Fit the receiver cell

   Unscrew the cap with your fingers. Fit the listed 337/SR416SW cell with the positive (+) face upwards; the lettered face identifies this side. Carefully screw the cap back on and check its alignment.

2. Check power on the table

   A powered Vip Pro receiver may make a low static sound. Check its cell orientation and cap alignment if the sound is very loud even outside the ear. A weak or discharged cell can also stop the receiver from responding.

3. Remove the cell after use

   A fitted cell is consumed even when the transmitter is not being used. Remove it between uses. Do not confuse the receiver’s cell with the rechargeable battery inside the transmitter.

1. Start with the unit off

   Use a quiet room. For Nano, put the extraction magnet together with the two Nano earpieces and lay them in direct contact with the induction unit. For Vip Pro, place the prepared receiver near the induction unit.

2. Switch on and check the prompt

   Press SOS briefly. Check for the “System ON” prompt, vibration or very quiet sound. A response tests the table audio path; it does not establish correct ear placement.

3. Check a telephone call

   Call the kit’s SIM number from another phone. Answer with one brief SOS press, or test automatic answering if you have configured that caller as the SOS contact. Check the microphone in this call and adjust the unit’s audio level.

If there is no response, check the charge, Nano SIM seating, SIM PIN setting, coverage, call service and audio level. Try another compatible Nano SIM if available before contacting support.

Identify the receiver and extraction parts

The extraction magnet and rod are separate from the two small Nano earpieces. The rod accepts the magnet at its base. Keep these parts identifiable; do not mistake the magnet for an earpiece. An optional Vip Pro receiver has a transparent removal thread.If fit or removal is unclear, stop and ask for model-specific guidance. Do not use sound alone to decide that a receiver has left the ear.

Position the transmitter

Position the induction unit between the neck and chest, with its connections supported. Its distance from the receiver affects the audio level.Keep the microphone opening clear of clothing and tape. The induction unit is not washable; keep its electronics and charging connection dry.The wired microphone can be positioned separately near the neck or sleeve; do not cover its opening.After use, hold SOS for 2 seconds to turn the unit off. Remove an optional Vip Pro cell. Clean the loose Nano earpieces, extraction magnet and rod before and after use. The kit instructions list water or isopropyl alcohol for these loose parts only, outside the ear; keep these liquids away from the induction unit and its electrical connections.